Step-by-step Guide On How To Hang A Canvas Art

Canvas painting may add a touch of class to your house. Whether it’s a historical artwork or a custom-made photo canvas, the final product will have clean lines, bringing in a contemporary addition to your interior.

The excitement and satisfaction you will experience once you observe your favorite canvas painting displayed in its perfect location is an additional benefit. However, installing this fabulous wall décor is not an easy task.

You may make mistakes, hammer nails in the wrong areas, and have to repeat the procedure many times, leaving you with nothing but a damaged wall.

I’m sure you’ve had similar experiences. Isn’t it enraging?

Now is the time to put your troubles behind since we are here to make hanging a canvas painting a delight for you!

The Essential Tools For Hanging A Canvas Print

To begin, you’ll need some essential tools for each of the steps mentioned below. You might currently have some of them at home, but if not, you can get them up at your nearest hardware shop.

  • Pencil
  • Screw Driver
  • Tape Measure
  • Spirit Level
  • Hammer
  • Wall Protection Pads

Steps On How To Hang A Canvas Print

1. Calculate the Right Height

The first step is to determine the height of the canvas center.

Place the canvas on a level surface and measure it using a tape measure or a ruler. Measure from the upper edge of the canvas to the lowest border and mark it down. Then, divide the height of the canvas by two to get the height of the middle area.

After that, increase the canvas center elevation by 57 inches. The middle of paintings at art galleries and museums is typically the exact inches from the ground since this is at eye level for the average individual.

To calculate how high the top of the canvas should be from the ground, multiply the height of the canvas center by 57 in (140 cm).

You will then use a pencil to indicate the elevation on the wall.

2. Mark The Wall

Utilize the measuring tape to determine the height of the wall where the canvas will be hung. Create a tiny dot or a clear cross form. This is the height of the canvas from the ground.

You may also use chalk instead of a pencil. I recommend that you do not nudge too hard since this may cause harm to the wall.

Mark the location of your canvas on the wall using a pencil. Keep in mind that the top of the canvas will be somewhat higher than your pencil mark.

If you’re using a sawtooth bracket when hanging a canvas print, measure and label the top of the rear panel.

If you’re using an eye hook, make a pencil mark in the middle. If you’re going to utilize a J-hook, create one or more pencil marks on the wall. This is determined by the number of hooks you use.

When you’re using adhesive tape, simply mark the place and focal point where you want to place the canvas.

3. Attaching Framing Tool To the Canvas

The next step is to secure the framing tools on the back of the canvas print.

When connecting a hanging wire to an eye hook, which is the most common and complex method, you should estimate 1/3 downwards from the top of the canvas on both sides.

Flip the canvas over and place it on a level surface, such as a table. After measuring, mark the 1/3 measurement along each vertical wooden stretcher bar with a pencil. This is where your steel eye screws will be installed. Before you continue, check if both sides are even.

After that, put two steel eye screws into each vertical hardwood stretcher-bar. Locate the marks you just created with a steel eye screw, and Insert the steel eye screw and twist it hard until it seems upright.

Make sure to screw the steel eye screws straight to avoid damaging the canvas.

The next step is to thread the wire through both eye screws. Insert each end of the steel wire through the steel eye screws and form a loop at each end after knotting it through the steel eye screws. Keep the steel wire reasonably loose but tight at the knots.

What about the procedure for attaching a sawtooth hanger?

First, determine which sawtooth hanger is appropriate for the weight of your canvas. Examine the sawtooth hanger labeling to make sure you’re getting one that can securely hold the weight of the canvas.

The bigger the canvas is, the bigger the sawtooth hanger you’ll require.

Upon the upper wooden stretcher bar, mark the canvas’s midpoint. Flip the canvas over to reveal the wooden stretcher bars and double-check that the top wooden stretcher bar is at the top.

Locate the central point using a measuring tape or a ruler and mark it with a pencil. The sawtooth hanger will be placed there.

Place the sawtooth hanger’s midpoint on the center mark. Remove the sawtooth hanger from the package and place it over the center mark on the wooden stretcher-bar of the canvas.

4. Hammer Hook or Nail

If you’re using an eye hook, hammer in a nail, or use a hook where you indicated the center with the pencil.

If you’re using a sawtooth bracket, hammer the nail at a bit of slant into the hanger hook. The angle of the nail will reinforce the hanging and ensure that the wall will bear the majority of the weight.

A nail should be inserted into either edge of the sawtooth hanger. Gently secure the sawtooth hanger in position and hammer a nail into each designated place to secure it to the wooden stretcher-bar. To ensure that the canvas hangs appropriately, ensure the sawtooth hanger is straight.

If you hammer in the nails with too much power, you risk damaging the canvas.

Place your J-hook on the wall if you’re using one. It comes with a nail that will go straight into the hook. On a bit of slant, hammer it in.

If you’re using adhesive tape, there’s no need to nail anything down.

5. Hang Your Canvas

Before proceeding to the last section, you may want to take a step back.

It’s time to double-check your canvas placement. Is it a straight line? Are there any nails or components missing?

Make any necessary adjustments. Also, if you have one, check it with a spirit level.

It’s not a good idea to hang your canvas in a humid environment, such as your bathroom or kitchen, or where it’ll be exposed to a lot of direct sunshine. They won’t last as long if you don’t.

Simply clean the canvas with a gentle, dry cloth to keep your canvas prints looking great.

When you already put the canvas in the appropriate spot and hung it correctly, now is the time to experiment with various methods to hang your canvas print.

Different Ways To Hang A Canvas Print


Small and medium canvases, such as 1 Panel Wall Art, will look best with nails. Choose nails that are appropriate for the size of the canvas.

Small nails will look great on a small 810 canvas, whereas a medium-sized nail will look nicer on a 1616 or 2030 canvas. Nails made of brass or steel must readily penetrate the wall without chipping or harming it.

Kindly remember that constantly hammering the nail is not required for this reason; this will guarantee that your drywall is damaged and chipped as little as possible.

Sawtooth Bracket

Sawtooth brackets vary in various sizes, so be sure you choose the right one for your canvas. The center of the frame must always have these brackets.

Sawtooth brackets are an excellent choice for small-to-medium-sized canvases since they provide a lot of rigidity. This is one of the easiest and most common methods for hanging wall art.

Eye Hooks

Highly qualified frame shops use eye hooks a lot, but you’ll be amazed how simple they are to use at home. Small eye hooks are sturdy enough to hold a canvas and occupy little space around the wall and the frame.

The advantage of this technique is that the art wire may be adjusted to ensure that the canvas precisely hangs as you want it.

J Hooks

J-hooks are an excellent choice when working with large or broad canvases, such as 5 Panel Wall Art. The hooks are available in a variety of sizes and with one or two nails. A basic, smaller hook would be ideal for lighter, smaller canvases, whereas hooks that need two nails will carry greater weight.

To figure out which choice is ideal for you, look at the package supplied by the manufacturer. To guarantee a secure hang, use two or three hooks around the wall.

When hanging a canvas that is considerably broader than it is tall, this is an excellent choice. For this technique, the measuring tape will be your best buddy.

Adhesive Strips

The most straightforward approach is to use adhesive strips. The majority of adhesive hanging solutions are designed to prevent wall damage. They’re simple to use and typically come with velcro and adhesive combo.

Before you begin, make sure to determine the weight of your canvas, as most adhesive strip items explicitly indicate the weight capability on their package, which usually ranges from four to sixteen pounds.

The manner you hang your canvas is just a matter of personal choice. What matters is that you properly exhibit your priceless canvas prints and artwork.

Share this post

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.